Find Out What Door Lock Replacement Tricks Celebs Are Using
From Shiapedia
Door Lock Replacement - What You Need to Know
If the locks on your door begin to exhibit signs of wear and tear, it's generally an ideal time to replace upvc door lock them. This could be due to experiencing difficulty turning the lock, or having a key that isn't fitting.
It is good to know that installing new hardware for your door locks is surprisingly easy. You only need to follow these simple steps.
Deadbolt
The deadbolt is the main protection of your door against forced entry. It is stronger and safer than the latch which activates the lock. So, you will want to ensure that the new deadbolt you purchase meets your needs. If possible, look for a deadbolt that's made with case hardened steel and no screw heads exposed on the outside to stop unintentional drilling. The interior side of the deadbolt must be inserted into the upvc door lock replacements frame to enhance security.
During installation, be sure that the bolt of your new deadbolt extends smoothly through the strike plate when you close and lock the doors. If it does not, use a wood chisel to make a mortise for the bolt hole into the strike plate and then put the deadbolt back in place. When you close and lock your door, be sure that the latch of the doorknob matches the deadbolt's hole.
Before installing your new deadbolt, check whether it's the same size of the old one. The majority of door locks have a template showing how far the bolt should be located above the doorknob. However, it's always recommended to consult a hardware expert if you are unsure what backset measurement you need for your doors. They will be able to direct you towards models that are compatible with your doors and the existing deadbolt opening.
Screw the bolt assembly into the hole in the door after making sure it's the right length. Screw the faceplate of the latch into the hole if the new deadbolt comes with one. It's a good idea to fix the latch faceplate onto the frame using the recommended screws in addition.
Some lock sets come with a decorative or "dummy" bolt, which lets you install the keyed-deadbolt and still have an operational latch. If you're using this type of lock, a dummy bolt should be installed with the same screws that are used for your latch faceplate, and it's important that the two fit together in a secure way to ensure maximum security.
Some deadbolts come with one cylinder that is only accessible from the inside using a thumb-turn, while others have a double cylinder that allows keyed and unkeyed entry. It is best to select an item that's commercial grade for maximum security. They are usually tested to withstand 250,000 cycles of open and close before being sold to homeowners.
Latch
The latch is the part that retracts the bolt when you shut or open the door. It's usually held in place by screws that are located on the side of the lock, however it can also be attached to the strike plate or the inside of the jamb. It's important that you replace a door lock with the correct one that matches your current hardware. You can verify this by putting the latch up to your existing hardware, or you can look on the label of a replacement. Dunn Lumber carries a variety of brands, however it's generally best to choose the same brand as your existing hardware to ensure you purchase an appropriate latch that fits correctly.
Some doors are equipped with a havep instead of a latch. A hasp is an elastic strap with a slot punched in it, which is able to be positioned over a staple. The staple is then attached to the door door frame by nail. When the door is shut, the strap pulls down on the staple and locks in the frame. A hasp is usually employed in commercial buildings since it is cheaper than deadbolts.
Like any mechanism that has moving parts, a lock can wear out due to repeated use over time. Sometimes the internal mechanism can "stick" or be difficult to turn. This will require the replacement of the entire lockset. Other times the exterior doorknob or handle will simply break, making it necessary to replace lock in upvc door it as well.
If your lock is stuck, you can apply some graphite to the keyhole. You can either spray some on the key or rub it onto the inside of the lock, then move the lock several times to work the graphite into the mechanism. You can also use a screwdriver to remove the knob and reveal the inside components and allow you to see what's going on inside.
After taking the knobs off and tightening the two or three setscrews on the edge of the cylinder by turning them clockwise. The faceplate needs to be removed and replaced. Surface-mounted rim locks come with an additional set of cylinder setscrews located on the back of the case that must be removed, along with the cover plate.
Strike Plate
The strike plate acts as a reinforcement and upgrade to a locking system. It is placed to the holes for deadbolts or master key system bolts. It helps keep intruders out by ensuring that the latch of the lock is held in the plate when the bolt is engaged. Apart from enhancing security, a high-quality strike plate can also improve the life of the lock.
Standard strike plates are flat metal plates with holes, or a series of holes, cut into them. It is secured, typically using screws, to the doorway's frame to give the latch an area to rest in when it closes. It is crucial that the strike plate is precisely aligned with the lockset to offer maximum protection against break-ins.
If the strike plate of the door is damaged, you should replace it as soon as possible. This will ensure that your door will close and latch correctly. The first step to replace patio door lock a strike plate is to make sure that it is properly aligned with the bolt hole inside the doorjamb. This can be done easily by placing a piece adhesive tape over the bolt hole and then testing the latch. If the latch does not catch then take off the tape. Then chisel it to ensure that the strike plate is flush with the doorjamb.
After the area has been chiseled, it is essential to use a larger bolt to fix the strike plate. The screws should be at minimum three inches long to ensure that they are securely secured to a stud in the trim board. If you do not install the screws that are longer or the wood inside the doorjamb may split in the event of a kick-in attack by a burglar and make the door vulnerable.
A professional locksmith can quickly replace the strike plate that has been damaged or worn. They can also put an entirely new strike plate on doors that have never had one before. They can also upgrade existing strikeplates to improve the security of a building and its aesthetics. This could help property owners draw in tenants looking for a safe and secure living environment and greater peace of mind.
Keys
The key cylinder of your lock is the part that accepts the key to move pins so that the internal handle can turn. The key cylinder is also the most crucial component of your door lock because it performs the job that locks were made to protect you, your family members and your belongings. Rekeying locks is a more cost-effective option than replacing a patio door lock them.
The process of replacing locks is more difficult than simply swapping out the existing handle-lock combo or deadbolt. A complete change in the lock requires removing the old cylinder and hardware from the door (including the handle in the case of a knob-lock combo) and then installing a new one in its place. While there are a number of DIY-friendly kits available that can be used to change a lock yourself but it is highly recommended that you consult a skilled locksmith to ensure the job is done right.
Before you can install an entirely new lock and cylinder it is crucial to have the right key for your house. A duplicate key won't perform as expected and could cause the lock's failure and make it impossible for you to open. A professional can prevent this from happening by ensuring that you have a an authentic, functioning key for your home.
The next step is to remove the faceplate, then the latch plate. You will need a screwdriver for the removal of the screws which hold them in place. You may want to leave them in place if the new plates are similar to the original ones. This will help you save time. If you have to replace them, make sure you don't overtighten screws as this can weaken their grip.
After taking off the plates, you will have to determine the proper measurement for the new lock. It is important to know the door's dimensions before visiting the hardware store. Although a lot of locksets available are designed to fit on a standard door's thickness, it is best to get them in advance. Be aware that doorknob locksets can be different sizes than deadbolt locksets, and commercial models may have an enlarged bolt or latch.
